JavaScript seems to be disabled in your browser. You must have JavaScript enabled in your browser to utilize the functionality of this website. There is also an extension kit available SA Read more. The plastic Gecko Gauges are completely safe on pre-painted siding when using the gauge properly and not over-tightening the gauge.
The metal versions, however, will leave marks on pre-painted siding. You want a snug fit on the siding. Be sure all windows, doors, and wall penetrations are properly flashed and sealed. Select trim that is compatible with the siding panels.
You want the trim to be thicker than the siding, to allow for proper sealing where the siding butts into the trim. Engineered wood siding typically butts into the trim pieces, so it is necessary to start by installing the trim at the windows and doors. This is much like building a frame around the windows, so be sure to account for the width of the trim when measuring to cut these pieces.
Outside corners are typically trimmed with two overlapping trim boards. For the inside corners, rip a square cross-section, like a 2 x 2, to allow the siding panels to butt squarely into the corner trim. Eave trim and roof trim can typically be installed later, once appropriate scaffolding is set up to safely reach and work on these areas.
Generally, a starter piece is installed underneath the first course to simulate the typical overlap and to orient the panel at the proper angle. Whether the substrate is plywood sheathing or foam insulation, most manufacturers require the siding to be fastened into the studs. Ring-shank nails are a popular choice for fastening the siding because they have screw-like rings that offer additional protection against nail pullout.
If you are using a pneumatic nail gun, be sure that the pressure of the nail gun is set to sink the nails flush with the surface of the wood. Being able to hold your siding in place while you are working with it is very important, and if you are working alone or are worried about the quality of help that you will have, it is important that you have the right tools to help you.
Siding gauges are great for helping you hold your siding in place and can take the place of having another person help you with your siding job, which is why they are an indispensable tool for replacing your siding. They will ensure that each piece of siding is level, which will allow you not only to complete your installation job significantly more quickly but also to ensure that the final result looks the best that it can.
Source: Houzz. Before you can replace any siding on your home, you will need to be able to remove it, which is why you have to have a zip lock tool. This tool has a handle that encloses a metal bar, complete with a small hook on the end. There is a bend in the tool to allow you a lot of control and force when removing the siding without having to put a lot of effort into popping it off of the home.
This tool is specifically designed to allow you to get underneath the bottom and the top edges of your siding where the pieces are interlocked without breaking them. You will use the zip lock tool to release your vinyl panels by inserting it into a loose area of the panel, wiggling it in, and then hooking the end of the tool onto the lip. By pressing down gently on the tool, you will be able to begin to release the panel from the joint.
This is why you need to make sure that you choose a tool that has the bend in the metal bar, as this is what is going to give you the power that you need. While you can use a utility knife to easily cut through your vinyl panels, if you want to speed up the process and finish as quickly as possible, then you will want to reach for a power saw instead. Make sure that you switch out the blade that you have on it and use one that is fine-toothed, as you want to decrease the chance that you will cause your vinyl panels to split or splinter.
When you are working in very cold weather, then you will want to make sure that you run the saw very slowly to prevent major cracking in the vinyl. Choosing a power saw is a little bit of a personal preference, as there are a few different types that will work for this job.
You can easily use a radial-arm or bench power saw, but if you prefer, then you can use a handheld power saw.
Of course, make sure that you have all of the safety gear necessary before operating a power saw, especially because bits of sharp vinyl can break off of the pieces that you are cutting and greatly damage your eyesight or cause other injuries.
Use protective eye gear, hearing protection, and heavy gloves in case you accidentally grab a sharp edge without realizing it. Vinyl is generally very easy to cut, score, and trim when you have a quality utility knife to use, making this tool one that you will want to keep with you at all times when you are working on this project. There are a number of different types and styles of utility knives on the market, and since they all have their own pros and cons, it comes down to personal preference when you decide what kind of knife is the right one for you.
If you want to be able to keep working without having to change your blade when it grows dull, then look for a utility knife that has snap-off blades, as you can easily remove the old and dull blade, revealing a sharp one underneath, and keep working without much of a delay.
While they may look like scissors or like pruners, tin snips are incredibly durable, able to cut through metal or vinyl without causing it to crack or break, and are perfect for cutting your pieces to the right size and for cutting out mitered sections.
While you will want to use a hand saw to cut pieces down to size, when you need more control over what you are cutting, then you need to go ahead and invest in a pair of tin snips. They offer a lot of control and will easily cut through your vinyl siding without any problems. Source: Amazon. When you are going to be attaching vinyl panels to the utility trim, then you need to make sure that you have a snap lock punch tool on hand.
This tool is very single-use but is indispensable when you are going to be installing vinyl paneling on your home. You can use this tool to easily and quickly secure the siding, as well as the skirting, to the finished trim underneath the window or along the top of the wall.
They work by creating notches in the panel. You want to place each notch about three inches away from the others, as you will then be able to lock the panel onto the utility trim when you slide them up and together.
0コメント